Unigas PN30 Installationshandbuch

Technical Documentation CIB Unigas - Campodarsego (PD)MANUAL OF- INSTALLATION- OPERATION- MAINTENANCEHEAVY OIL BURNERSPN30SINGLE STAGE VERSIONM03930CC

PART I: INSTALLATION MANUAL10Fig. 9 - Hydraulic diagram 3ID0012 for 2 or more burners OIL CIRCUITPRE-HEATED WATER CIRCUITPRE-HEATING 50°CPRE-HEATING

PART I: INSTALLATION MANUAL 11REGULATIONSPump primingBefore regulating, the oil pump must be primed as follows:! Before starting up the burner, make s

PART I: INSTALLATION MANUAL12SELECTING THE OIL NOZZLESTab. 1 - Nozzle flow rate in relation to oil pressureOIL PUMPS Key1 Pressure adjustment2 Pump pr

PART I: INSTALLATION MANUAL 13AIR FLOW REGULATIONSlacken the screw VBS and set the required air flow working directly on the air damper. At the end of

PART I: INSTALLATION MANUAL14VISCOSITY VS TEMPERATURE DIAGRAM Fig. 13 VISCOSITY vs. TEMPERATURE DIAGRAMBEST VISCOSITY RANGE FOR APROPER ATOMIZATI

PART I: INSTALLATION MANUAL 15BURNER IGNITION PROCEDUREOil pump! Check that mains voltage corresponds to the voltage indicated on the rating plate.! C

PART II: OPERATION MANUAL16LIMITATIONS ON THE USE OF THE EQUIPMENTTHE BURNER HAS BEEN DESIGNED TO OPERATE ONLY AFTER IT HAS BEEN CORRECTLY CONNECTED T

PART II: OPERATION MANUAL 17Single stage burners front panelFig. 15a LegendaA Main on/off switchB Shut down indicator lightD Solenoid valve opening i

PART III: MAINTENANCE MANUAL18Carry out the following maintenance operations at least once a year. If the boiler is used seasonally, maintenance shoul

PART III: MAINTENANCE MANUAL 19Correct position of electrodes and combustion head To guarantee efficient ignition, the measurements indicated in Fig.

NOTICES2NOTICESTHIS MANUAL IS SUPPLIED AS AN INTEGRAL AND ESSENTIAL PART OF THE PRODUCT AND MUST BE DELIVEREDTO THE USER.INFORMATION INCLUDED IN THIS

PART III: MAINTENANCE MANUAL20Checking detection currentTo measure the detection signal, follow the diagram in Fig. 19.If the signal is not within the

PART III: MAINTENANCE MANUAL 21TROUBLESHOOTINGDOES NOT START UPCONTINUES PRE-PURGUEBURNER STARTS UP WITH COLD OILDOES NOT IGNITE AND GOES TO SHUT DOWN

PART III: MAINTENANCE MANUAL22ELECTRICAL DIAGRAM 04-649 - Complete key BR Pre-heating resistor contactor coilBV Fan motor contactor coilCAV Fan motor

PART III: MAINTENANCE MANUAL 23ELECTRICAL DIAGRAM 04-649

PART III: MAINTENANCE MANUAL24SPARE PARTS

PART III: MAINTENANCE MANUAL 25D E S C R I P T I O N P N 3 0 1 ELECTRICAL SWITCHBOARD 659.03...2 CONTROL UNIT TERMINAL BOARD 20304093 CO

APPENDIX - TECHNICAL CHARACTERISTICS26LANDIS LIGHT OIL BURNERS AUTOMATIC CONTROLLER LOA24 27LANDIS OIL BURNERS AUTOMATIC CONTROLLER LOA44 29SUNTEC P

APPENDIX - TECHNICAL CHARACTERISTICS 27LANDIS LIGHT OIL BURNERS AUTOMATIC CONTROLLER LOA24UseLOA... safety devices are intended for use solely with QR

APPENDIX - TECHNICAL CHARACTERISTICS28Technical characteristicsVoltage 220V -15%..240V+10% or100V -15%...110V+10%Frequency 50...60Hz +/- 6%External fu

APPENDIX - TECHNICAL CHARACTERISTICS 29LANDIS OIL BURNERS AUTOMATIC CONTROLLER LOA44OperationBurners without fuel pre-heaterStart-up, thermostat and p

NOTICES 33) GENERAL INSTRUCTIONS DEPENDING ON FUEL USED 3a) ELECTRICAL CONNECTION! For safety reasons the unit must be efficiently earthed andinstalle

APPENDIX - TECHNICAL CHARACTERISTICS30Technical characteristicsVoltage 220V-15%..240V+10% or100V-15%..110V+10%Frequency 50...60Hz _6%External fuse max

APPENDIX - TECHNICAL CHARACTERISTICS 31SUNTEC PUMPS E SERIEThe SUNTEC oil pumps incorporate a pressure regulating valve with cut-off function. The E p

PART I: INSTALLATION MANUAL4 TECHNICAL DATA BURNER MODEL IDENTIFICATIONBurners are identified by burner type and model. Burner model identificat

PART I: INSTALLATION MANUAL 5OVERALL DIMENSIONSFig. 4PERFORMANCE CURVEABBLCCLDEFGKZVWMPN30 520 160 350 680 870 270 450 720 131 400 160 155 219 M10BACK

PART I: INSTALLATION MANUAL6MOUNTINGS AND CONNECTIONSImballoThe burners are despatched in wodden crates of dimensions 10070 x 740 x 840 (W x H x D).Pa

PART I: INSTALLATION MANUAL 7ELECTRICAL CONNECTIONS! Remove the front panel of the electrical board on the burner.Carry out the connections in the pow

PART I: INSTALLATION MANUAL8HYDRAULIC DIAGRAMS 3ID0010 E 3ID0012 - Complete key1 Oil storage tank2 Foot valve3 Oil storage tank pre-heating coils (1)4

PART I: INSTALLATION MANUAL 9OIL SUPPLY PIPING INSTALLATION DIAGRAMFig. 8 - Hydraulic diagram 3ID0010 for 1 burner installations OIL CIRCUITPRE-HEATE